Jartel, Sukiswo Sukiswo

Presentasi berjudul: "Jartel, Sukiswo Sukiswo"— Transcript presentasi:

1 Jartel, Sukiswo Sukiswo sukiswok@yahoo.com
Attenuator Sukiswo Jartel, Sukiswo

2 Outline Pendahuluan Passive Design Active Design Pi Attenuator
Tee Attenuator Bridged T Attenuator Active Design Narrowand Active Variable Attenuator Broadband Active Variable Attenuator Jartel, Sukiswo

3 Pendahuluan Attenuator : device yang digunakan untuk : Attenuator :
Mengatur level signal Mengontrol impedansi yang tidak match dan Mengisolasi tahap rangkaian Attenuator : Passive Active Jartel, Sukiswo

4 Passive Design Passive Design Pi Attenuator Tee Attenuator
Bridged T Attenuator Jartel, Sukiswo

5 Pi Attenuator Rangkaian Pi Attenuator Jartel, Sukiswo

6 Pi Attenuator Besarnya komponen R1, R2 dan R3 sbb : Jartel, Sukiswo

7 Pi Attenuator Jartel, Sukiswo

8 Tee Attenuator Rangkaian Tee Attenuator Jartel, Sukiswo

9 Tee Attenuator Besarnya komponen R1, R2 dan R3 sbb : Jartel, Sukiswo

10 Tee Attenuator Jartel, Sukiswo

11 Bridged Tee Attenuator
Rangkaian Bridged Tee Attenuator : Jartel, Sukiswo

12 Bridged Tee Attenuator
Besarnya komponen R1dan R4 sbb : Jartel, Sukiswo

13 Active Design Active Design Narrowand Active Variable Attenuator
Broadband Active Variable Attenuator Jartel, Sukiswo

14 Narrowand Active Variable Attenuator
If we use the bridged-T network as a basis of an active attenuator we need to add the bias circuits to complete a basic design. The circuit has been set up such that the currents through D1 and D4 are inverse to each other ie when D1 current is high then D4 current is low and visa versa. When the PIN diode is on (high current)is has low attenuation. So when D1 is on and D4 is off, the two R’s and D4 are out of circuit and the attenuation through the circuit is low. Jartel, Sukiswo

15 Narrowand Active Variable Attenuator
When D1 is off and D4 is on the signal instead of passing through D1 will pass to ground via D4 and the circuit will be in a high attenuation state. Intermediate currents through D1 & D4 will allow attenuation from max to min. This circuit is Bridged T attenuator, where resistors R1 & R4 have been replaced by PIN diodes D1 and D4. Jartel, Sukiswo

16 Narrowand Active Variable Attenuator
Rangkain sbb : Jartel, Sukiswo

17 Narrowand Active Variable Attenuator
A typical microwave PIN diode is from Agilent HSMP-3810 has a low resistance of 10 ohms and a high resistance of 1500 ohms. Jartel, Sukiswo

18 Narrowand Active Variable Attenuator
Therefore, using such a device we could design an attenuator with the following min and max attenuations: Jartel, Sukiswo

19 Narrowand Active Variable Attenuator
Jartel, Sukiswo

20 Broadband Active Variable Attenuator
In many situations it is better to have a broad-band attenuator that can be used at many different frequencies. So for example assume we to design a broad-band attenuator with the following parameters Jartel, Sukiswo

21 Broadband Active Variable Attenuator
The first thing we need to do is select a Pin diode that is designed for these frequencies. In this case a MaCom MA4P202 PIN diode was chosen as it’s operating frequency range is specified as 50MHz to 18GHz and is available in chip form. The broad-band attenuator uses Lange couplers to provide a wide bandwidth attenuator Jartel, Sukiswo

22 Broadband Active Variable Attenuator
Jartel, Sukiswo

23 Broadband Active Variable Attenuator
In some circumstances we want to be able to switch in a fixed amount of attenuation. The easiest way of doing this is to use two SPDT FET switches and a broad-band fixed attenuator as shown in Jartel, Sukiswo

24 Broadband Active Variable Attenuator
Switches are formed by GaAs SPDT switches eg MA4AGSW2 50MHz to 70GHz SPDT MMIC. Jartel, Sukiswo

25 Soal Design attenuator dengan atenuasi 5 dB, impedansi input 60 , impedansi output 50  dan tentukan besarnya komponen yang digunakan jika : Digunakan Pi Attenuator Digunakan Tee Attenuator Jartel, Sukiswo